If you keep getting stuck in the software firmware upgrade as shown below, please use the following upgrade tool to solve your problem
Cart
Your cart is empty
If you keep getting stuck in the software firmware upgrade as shown below, please use the following upgrade tool to solve your problem
please check the cantilever model installation video
You can download the Special Edition to enhance your sound with instructional upgrades
Please check the documentation
Please check the documentation
Please check the documentation
Software Download:
https://www.maono.com/pages/maono-link-software
Use unidirectional cardioid mics which have a rear rejection that means no pickup from back side. Then you can use stage monitors facing you in the middle of the stage. And mic won't pickup them.
5V / 100mA - 230mA
48kHz/24Bit
Not necessary, because the PD200X is a dynamic microphone
Use unidirectional cardioid mics which have a rear rejection that means no pickup from back side. Then you can use stage monitors facing you in the middle of the stage. And mic won't pickup them.
5V / 140mA-0.8W
support@maono.com
48kHz/24Bit
Not necessary, because the PD400X is a dynamic microphone
Use unidirectional cardioid mics which have a rear rejection that means no pickup from back side. Then you can use stage monitors facing you in the middle of the stage. And mic won't pickup them.
5V / 130mA-0.7W
please contact us via email:support@maono.com
With this drive, the sound card can be recognized and used on the computer. It is a necessary driver for using PS22 on the computer.
Please close your anti-virus software and then reinstall the driver.
PS22 is a sound card designed for recording, if you need sound effects, please add them in your DAW.
MacOS built-in driver, no need to install, you can use it directly.
There are PreSonus Studio One, Cockos Reaper 6, Ableton Live, FL Studio, Apple Logic Pro, Steinberg Cubase, you can visit the official website to download the software.
3.5mm TRRS output - Duplicates the main output signal. Can be used to connect to a phone to do live streaming via a TRRS to TRRS cable (not included)
You can connect your phone to the PS22 using the USB-C socket.
Note: iOS only supports iPhone 15
Is the [POWER SOURCE] switch set properly?
The power indicator does not light when power is not supplied to the device.Move the [POWER SOURCE] switch to the [5V DC] jack side when using AC adapter or move the switch to [USB-C] jack side for bus-powered supply (computer only)
• Please check if the podcast console has power, please charge it, and then turn it on.
• You need to long-press the " " for more than three seconds to turn it on.
• Please check whether the external audio source is connected to the 'Music Input' interface of the podcast console.
• Please check whether the 'Music' volume control knob on the right is turned on.
• Please check the volume of the accompaniment device.
• Turn on LOOP BACK
• Please check whether the headphone cable is inserted into the correct interface. It should be inserted into the "headset" or "Output" interface.
• Please check whether is the "Monitor" of the sound card upwards. You can gradually increase the volume by sliding it up.
• Plug headphones into OUTPUT or HEADSET jack
• Please check whether the microphone is correctly connected to the microphone interface. If not, please try again.
• Please check whether the microphone knob on the left is turned on. Turn the knob clockwise to increase the microphone volume slowly.
• Please check whether is the "monitor fader" of the sound card upwards. You can gradually increase the volume by pushing it up.
• Please confirm with your microphone dealer whether your microphone can be used with this podcast console, or consult us for the recommended microphone model.
• Please check whether the "recording" knob on the podcast console is turned on, and rotate the "recording
• knob" clockwise to slowly increase the volume of the live broadcast.
• Please check whether the podcast console "MAONO AU-AM200" has been set as the default playback and recording device of the live broadcast software. If not, please set refer to the " Live Streaming on the Computer " part.
Turn off or turn down ECHO effect
It doesn't work on a voice call, it works on podcast or live streaming
Please keep 2 inches away from your mouth to the microphone
We don't provide an extra OTG adapter, you should connect your phone with the microphone through the OTG adapter which is included in your iPhone package
This audio interface just can only be used with a microphone which comes with a 3.5mm plug
It should be connected with a 3.5mm to 6.35mm adapter, then to guitar
Please turn down all the volume temporarily
• Please use line 1 to connect the USB-C port of the Audio interface, and use line 2 to connect to the computer. (Note: Do not fold the wire during use to avoid damage.)
• Please check the computer's sound settings after the connection is complete. Both the input and output are' MAONO AU-AM200 '(right-click the speaker on the right side of the desktop to open the sound settings)
• When you need to record the computer accompaniment sound, please turn on the loopback function.
For the smartphone used for podcast/ Streaming, please insert THE POD1/2/3 interface; for the smartphone used for playing accompaniment, please insert the Music Input jack. In addition, you can also play accompaniment Music through the Bluetooth connection of the smartphone.
OPENING is the volume down key, and LAUGHTER is the volume up key.
You need to press the light button on the side of the sound card 6 times, and the light of each button will slowly diminish to disappear.
which cannot be input and output simultaneously. (The Bluetooth is only for wireless accompaniment playback)
You need to turn up the REC knob above the audio mixer to output the sound.
We are working on an upgraded version that can turn off the monitoring function, so stay tuned
Recording: Turn the product on, connect it with either one microphone, external audio input device, Bluetooth device. Turn on the"LOOPBACK" mode. Hold any custom key until the button light flashes to start recording. The audio input will be recorded and saved. Release the button to end the recording.
Note: If you do not release your hand during recording, the recording will stop automatically when there is not enough space, and the light will automatically turn off.
• Please check if the podcast console has power, please charge it, and then turn it on.
•You need to long-press the for more than three seconds to turn it on.
•connect to the computer that is charging the device
•Use ordinary 5V 1A or 5V 2A size phone charging head
Please turn the recording knob to the appropriate range
•Powering on the sound card, the Bluetooth indicator will blink, Bluetooth search and
automatically pair with the paired mobile phone, then the indicator light turned to solid
•Long press the Bluetooth button for 2 seconds, the indicator will turn off and end pairing
It doesn't work on a voice call, it works on podcast or live streaming
•The switch on the side does not select the correct gain.
•The maonocaster E2 sound card has the built-in gain that provides sufficient gain for all microphone types, including low output dynamic microphones. When in use, you can adjust the switch on the side to select gain 50dB or 60dB to choose the gain multiplier and get the best results
No, the Maonocaster E2 does not support the connection of USB microphones.
No, the E2 is not a USB host device and will therefore not allow the connection of Bluetooth headphones.
The Maonocaster E2's microphone channels feature studio-quality preamps that can provide enough gain for all microphone types, including low-output dynamic microphones. You can change the gain multiplier of the side microphone setting to get the right effect for your use
We don't provide an extra OTG adapter, you should connect your phone with the microphone through OTG adapter which is included in your iPhone package
Recording can be achieved by using 6.35MM plugged into the instrument port
Take out the cable from the box, connect the computer and sound card ends respectively, after the connection is completed, please check the computer's sound settings. Input and output are set to "MAONO AME2" (right-click the speaker icon on the right side of the desktop to open the sound settings)
Press the A/B/C button to record a 1-minute audio effect, and press the Loop Button to repeat playing an audio effect. Press the other 8 buttons to record the 20s(Max)audio effect.
•By default, there is no customized audio effect.
•Recording: with an audio card on, connect it to mic/external audio input device/Bluetooth devices, and long-press any custom button for more than 3 seconds. Release press until the indicator slowly blinks and enters recording mode. Short press the button again to stop recording or record until the indicator stops blinking, which indicates max time length audio is recorded.
•Note: Each custom audio effect button has limited storage, when there is no storage left, it will stop recording and the indicator will go off automatically.
AU, Audacity, sound forge
The lamp is on by default, hold the power button for 1s to turn off light
•Please set the 'MIC1 SETTING' on the side of the audio interface to the correct position
• The microphone in the package needs to be placed in the 40dB gear
• If you need to connect your own microphone, please according to your microphone's sensitivity or contact us.
• Please adjust the 'MIC1 SETTING' on the side of the audio interface to 40dB
• Adjust 'MIC①' to the middle gear
• Adjust the 'LOW/MID/HI' to the middle gear
• Adjust 'OUTPUT' to the middle gear
• Please be 7-8in away from the microphone for the best recording experience
You can adjust each knob to the middle before using
• AUX: Adjusts the input accompaniment sound
• LOW/MID/HI: Adjust the high and low parts of the vocal input from the microphone
•INST: Adjusts the volume of the instrument input from the 'INST' jack
• PITCH: Interesting voice change adjustments
• MONITOR: Adjust the volume of your monitor through headphones
•OUTPUT: Adjust the volume of the output to your phone/computer
•MIC①②: Adjust the volume of the microphone input
• PAD VOL: Adjusts the volume of the custom effect created by your input
• DEPTH: Adjusts the depth of the reverb
• DECAY TIME: Adjust the reverb time
• Please adjust 'MIC①②' to increase the sound of the microphone
• Adjust 'MONITOR' to increase the monitoring sound
• Adjust 'AUX' to increase the sound of the accompaniment music
•Adjust 'OUTPUT' to increase the sound output to the smartphone/computer
• The monitored sound from headphones and the recorded sound are controlled by different knobs
•Adjust 'MONITOR', adjust the monitoring sound from the headphone
•Adjust 'OUTPUT', adjust the sound output to the smartphone/computer
•Powering on the sound card, Bluetooth indicator will blink, Bluetooth search and
automatically pair with paired mobile phone, then indicator light turned to solid
•Long press Bluetooth button for 2 seconds, indicator will turn off and end pairing
• Make sure the 'OUTPUT' knob is on and turn up the output volume
• Turn on the 'LOOPBACK' button
• Please make sure that the phone connected to the 'Live output' or the computer connected to the 'USBC' is correctly recognized
• Please check if the DRY/WET button is off
• please turn on the LOOPBACK button, if you want to record to your computer
1. Please do not hold the microphone by hand, please fix the microphone on the stand.
2. Check the connection status of the cable and the microphone interface is firmly connected.
3. Do not use a hub! First change the computer USB port connected by the audio interface, if it is a desktop computer, please connect to the USB port on the back of the host.
4. The noise of the audio interface itself or the environmental noise in normal use, the solution is to use it in a quieter environment.
5. The microphone gain is too high or the environment is noisy, causing the ambient noise picked up by the microphone to exceed the audio interface's noise reduction threshold. The solution is to reduce the microphone gain.
6. The interface of the computer device you are using is old or poorly grounded, or the power circuit connected to it is old, causing leakage and continuous current noise. Please try another computer device in a different environment or switch to a mobile phone for testing.
7. Electronic devices with strong radiated signals in the vicinity of the microphone, for example: wireless routers/video lamps, will produce interference noise. Please use the microphone in a different environment, for example: if the current location is the living room, please use it in the bedroom instead.
8. The noise caused by software incompatibility, please change to use the computer recorder for recording, and close third-party software to avoid software conflicts or noise caused by effects.
9. If you use it on a mobile device, Apple devices must use MFI-certified cables, and other brands should use original cables as much as possible.
10. If none of the above solves the problem, please record audio and take photos or videos of the audio cable connection. Send them to us so we can assess your problem
You can connect active speakers through the 'Headphone' interface.
You can adjust each knob to the middle before using
AMC2 Maonocaster has built-in gain to provide sufficient gain for all microphone types, including low output dynamic microphones. The GAIN knob on the panel can be adjusted to the right position when in use to get the right effect
We do not provide additional OTG adapters, you should connect your phone and AMC2 via OTG (the adapter must be the original official Apple adapter)
Recording can be achieved by using 6.35MM plugged into the instrument port, but it is not recommended, because AMC2 NEO is a two-in-one interface for microphones and instruments, and only one of them can be used, not both.
AU, Audacity, etc...
It doesn't work on a voice call, it works on podcast or live streaming
No, the Maonocaster AMC2 NEO does not support the connection of USB microphones.
No, the AMC2 NEO is not a USB host device and will therefore not allow the connection of Bluetooth headphones.
AM100 no latency, you use the software in the computer real-time monitoring function of the delay, it is recommended to adjust the parameters of the application, or use the computer's own recorder to record
We publish audio import software programs compatible with Windows and macOS in our "Manuals and Drivers". They are placed in the same location. You can check them carefully. If you can't find them, you can contact our support and they will answer your questions
AU-AM100 has two monitor jacks and two microphone jacks, can meet two people at the same time using monitor headphones and microphones
AU-AM100 doesn't have an SD card interface. If you want to save to an SD card, we recommend that you use a computer to record, and then transfer the recorded audio files from the computer to the SD card
Please check the documentation
Please check the documentation
Please check the documentation
Please check the documentation
Please check the documentation
Please check the documentation
Please check the documentation
Please check the documentation
Please check the documentation
you can refer the attachment: Fix sound problems on PC
192kHz/24Bit
you can refer the attachment: How to connect the microphone to the computer
That whistling sound is called Audio feedback and caused because of an endless loop caused when the mic picks up the sound of the loudspeakers (stage monitors or pa speakers) and sends it back to the loudspeakers to amplify and pick up again, resulting in 1 particular frequency getting boosted depending upon the resonance of the room, the speakers, etc.
Ways to correct /avoid feedback?
1. Face the speakers away from the mic or place them farther away.
2. Lower their volume or mic gain
3. Use unidirectional cardioid mics which have a rear rejection that means no pickup from back side. Then you can use stage monitors facing you in the middle of the stage. And the mic won't pick up them.
4. Ring out the speaker - deliberately create feedback by taking the mic closer to the speaker. When feedback happens, check the frequency on a real-time analyzer and cut it using channel eq or graphic eq.
5. Use a feedback reducer
you can refer the attachment : USB not Recognized
you can refer the attachment : USB Microphone not Working on Mac
When the transmitter starts the connection function, it cannot connect to the receiver, try to use the phone
SIM card pin inserted into RESET hole and pressed for 3 seconds to start the reset function, then try to connect.
Cannot
Cannot,This feature is supported on WM821, and you can purchase WM821
Cannot
When the transmitter starts the connection function, it cannot connect to the receiver, try to use the phone
SIM card pin inserted into RESET hole and pressed for 2 seconds to start the reset function, then try to connect.
yes
The use of conventional cell phone charger can be charged, rechargeable battery, computer USB port
Please tear off the bottom of the insulation tape
Low-cut function can shield the surrounding noise, ambient sound, so that the sound is more clean
Align windshields and microphone jacks, then push in the direction of the Maono logo to complete the installation
1. Please check if the connection is correct, TRRS (Four rings) connects to the phone, TRS (three rings) connects to the microphone
2. Please connect the audio cable to the microphone OUTPUT jack
3. When using the phone does not have a 3.5 MM headset hole, please connect the phone through the On the Go adapter cable, On the Go adapter cable, please use the original, to avoid connection failure and poor sound quality problems
1. Your wireless microphone is not successfully connected to the phone, you can use the recorder to record the sound, and then gently tap near the charging port, if there are sound fluctuations, the microphone is not successfully connected, please reconnect the device
2.WM821 has 6 volume levels, short press the receiver A or B button to adjust the volume of the corresponding transmitter
1.The receiver can switch between "Merged(MIX)" and "Split(AB)" by pressing the power switch button.
2.This allows you to record each transmitter onto separate channels on the output ('Split' mode) or combine the two into a single output ('Merged' mode). When it's in 'Split' mode, there will be two output level meters, when it's in 'Merged' mode, there will be just one.